S5010Alphanumeric keypad
C&K Sierra manuals
Also known as Sierra S5832 and S5000
Start hereS5010 / S5011 / S5012 Alphanumeric Keypad User ManualUser guide · 72 pages · 847 KBRead it nowKeypad cheat sheet
Arm (away)your code
- Close doors and windows. Wait for READY on the display (LED keypad: the Ready light is on).
- Key in your four-digit code.
- The Arm light blinks through the exit delay. The keypad may beep, faster in the last ten seconds.
- Leave and close the door before the exit delay ends.
- If your installer has turned on quick arming, hold Home for 2 seconds instead of keying your code.
Arm while homeHomeyour code
- Close the outside doors and windows. Wait for READY on the display (LED keypad: the Ready light is on).
- Press Home, then key in your code. The alphanumeric keypad asks for it: TO ARM, ENTER CODE NOW.
- This is home-arming: doors and windows are armed, and you can move about inside.
- LED keypad: the Arm light is on and the inside zone lights blink.
- No entry delay (instant home-arming): hold 9 for 2 seconds, then your code. LED keypad: code first.
Disarmyour code
- Come in by a door that has an entry delay.
- The Arm light blinks during the entry delay, and the keypad may beep.
- Key in your code. It is the same whichever way the system was armed.
- Keying your code during the exit delay cancels arming.
Bypass a zoneBypass2-digit zoneyour code
- Each detector or door contact is a zone. An open one shows FAULTED and its number (LED keypad: its zone light is on).
- Press Bypass, then the two-digit zone number (05 for zone 5), then your code.
- If your installer has turned on quick bypassing, leave the code out.
- LED keypad: the zone's light blinks. A 3-second tone means that zone can't be bypassed.
- Repeat to restore it. Disarming restores bypassed zones, except 24-hour zones.
Alarm memoryholdCANCEL
- Alphanumeric keypad: ALARM and the zone number show. LED keypad: that zone's light blinks fast.
- To cancel an alarm, press CANCEL, then key in your code.
- Write down the zone, then hold CANCEL for 2 seconds until you hear two beeps.
- That clears the alarm from the keypad and resets the detectors.
Chime on or offhold4master codehold4master codeHomeCANCEL
- Hold 4 (chime) for 2 seconds until two beeps, then key in the master code.
- Alphanumeric keypad: CHIME ON or OFF shows. Press Home to change it, then CANCEL. Press Bypass instead to leave it unchanged.
- LED and icon keypads: three beeps mean chime is now on; one long beep means off. No further keys are needed.
- With chime on, opening a protected door or window gives three beeps.
Panic alarmholdPOLICEorholdFIREorholdMED
- These keys only work if your installer has turned them on.
- Hold POLICE, FIRE or MED for 2 seconds. The alarm may be silent, depending on the setup.
- Alphanumeric keypad: the display shows POLICE ALARM, FIRE ALARM or EMERGENCY ALARM.
- To cancel it, press CANCEL and key in your code.
Change a codehold8master codeuser numbernew codethenholdCANCELhold8master codeuser numbernew codeHomethenholdCANCEL
- Hold 8 (user prg) for 2 seconds until two beeps, then key in the master code.
- Key the two-digit user number. On an icon keypad, press Home next.
- Key the new four-digit code. Alphanumeric keypad: press Home at ENGLISH? to choose English.
- On any keypad, hold CANCEL for 2 seconds to finish.
- To delete a code, change it to 0000. Change the factory master code.
Set the date and timehold2master code
- Hold 2 (clock) for 2 seconds until two beeps, then key in the master code.
- LED and icon keypads: key the day, month and year (two digits each), pressing Home after each.
- LED and icon keypads: enter the hour in 24-hour time, then minutes (two digits each), pressing Home after each.
- Alphanumeric keypad: the time shows. Press Home, key four digits, then 1 for am or 2 for pm.
- Alphanumeric: press Bypass when the time is right. For the date: Home, then day, month, year (two digits each), then Bypass.
Trouble lightshold3
- PRESS SERVICE on the display (LED keypad: the Service light) means something needs attention.
- The keypad beeps twice every 30 seconds for a minute. Key your code between beeps to stop it.
- Hold 3 (service) for 2 seconds to see the message. Press 3 again for the next one.
- Alphanumeric keypad: press CANCEL when done. The table gives its display messages; the Power light entry applies to both keypads.
- LED keypad: use the zone-light patterns in its manual. Keep pressing 3 to see each fault; it exits after the last one.
Pages 8, 51 and 52 of the S5010 / S5011 / S5012 Alphanumeric Keypad User ManualPages 9, 52 to 54 of the S5030 / S5031 / S5032 LED Keypad User ManualAC POWER LOSS Power cut. Set the clock again once the power is back. BROWN OUT Partial power loss. Call for service if it doesn't clear when power returns. PANEL LOW BATT Backup battery low. Let it recharge overnight, then call for service if it stays. GROUND FAULT Wiring short to earth. Call for service. PHONE #1 NO RPT The monitoring centre didn't answer. If your phone line works, ring them. PHONE 1 CUT Phone line 1 isn't working. If your phone works, ring the monitoring centre; if not, your phone company. BELL SUP FAIL The outside siren needs service. Power light off / blinking slowly Running on battery / the battery is about to fail.
Why is my keypad beeping or showing a trouble light?
Most keypads beep or light up a trouble indicator when something needs attention, such as a low backup battery, a power cut or a lost phone or internet connection. Your user guide explains what each light or code means on your model. If it keeps happening, or you are not sure, call your installer or monitoring company.
All C&K Sierra manuals
User guides 3
Installer manuals 1
Nothing here matches that.
Try a shorter search, or search every brand.
More C&K models
Is anyone watching your alarm?
An alarm that only makes a noise relies on someone hearing it. A monitored alarm reports to our A1 graded, NZSA approved control room, watched 24/7 by a team that is New Zealand owned and operated. We can monitor most existing alarms, so you may not need a new one. Thinking about a new alarm or security cameras? Ask us for a quote.
Prefer to talk now? Call us on 0800 339 999.
Home: alarm monitoringBusiness: business monitoringInstaller: bureau monitoring
Manuals are the property of their manufacturers and are provided for reference only; their inclusion here does not imply any endorsement by the manufacturer.