Brinks BHS-1000 manuals

Keypad cheat sheet

• Arm (away)0ormaster code

  • Close all protected doors and windows. The green ready light must be on before the system will arm.
  • Press 0, or key in the master code, pressing the keys slowly. The system turns on.
  • On a BHS-1000C as supplied, the exit time is 80 seconds. A door left ajar sets off the alarm when it ends.

  Page 1 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPage 6 of the Brinks BHS-1000C Panel Introduction and Programming Chart
• Arm while home#60or#6master code

  • The card calls this bypassing the motion detectors: the inside is off and the doors and windows are on.
  • Press #, 6, then 0, or #, 6 and the master code.
  • Add # 5 at the end to make the doors instant too: opening one then sets off the alarm with no entry delay.
  • On a BHS-1000C, # 5 also ends the exit time at once: the doors are instant straight away.

  Page 1 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPage 2 of the Brinks BHS-1000C Panel Introduction and Programming Chart
• Disarmmaster code

  • Key in the master code, pressing the keys slowly. The system turns off.
  • If an alarm goes off, wait for your monitoring company's call.
  • Accidental alarm on a BHS-1000C? Your code, then # 9. Within 20 seconds of a burglary alarm, nothing is reported.
  • After those 20 seconds, # 9 sends a cancel signal with the alarm.

  Page 1 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPages 2, 6 of the Brinks BHS-1000C Panel Introduction and Programming Chart
• Clear the keypad#0

  • Keyed in something wrong? Press # then 0 to clear the keypad, then start again.
  • On a BHS-1000C you can instead key in the whole code again: it only reads the last 3 digits.
  • On a BHS-1000C, 15 number keys pressed without a valid code lock the keypad out.

  Page 1 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPage 6 of the Brinks BHS-1000C Panel Introduction and Programming Chart
• Reset smoke detectors#8

  • Press # then 8 to reset the smoke detectors.
  • The same keys test the siren and battery: see Test the system.

  Pages 1 and 2 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference Card
• Panic alarm

  • The keypad has a police, a fire and a medical emergency button. Press the one you need.
  • The alarm goes on and a signal is sent. Wait for your monitoring company to call.
  • Key in the master code to reset an emergency button alarm.

  Police, fire or medical button pressed	Alarm on and a signal sent
  Master code keyed in	The emergency button alarm is reset

  Page 2 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPages 3, 5 of the Brinks BHS-1000C Panel Introduction and Programming Chart
• Change a code*master codeuser numbernew code

  • Auxiliary codes are extra codes besides the master code. The card gives their numbers as 1, or 2 to 7.
  • Press *, key in the master code, then the auxiliary code's number, then the new code. Press the keys slowly.
  • The new code is saved in the system.
  • On a BHS-1000C, every code is 3 digits.

  Page 2 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPage 6 of the Brinks BHS-1000C Panel Introduction and Programming Chart
• Test the system#7or#8

  • Press # then 7 to send a test signal. Your monitoring company will call you.
  • On a BHS-1000C, a short siren blast and a beep from the keypad confirm the test.
  • Press # then 8 to test the siren and battery. No signal is sent unless the battery is low.

  Page 1 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPage 5 of the Brinks BHS-1000C Panel Introduction and Programming Chart
• Trouble lights*master code0

  • A blinking trouble light can be reset once the green ready light is on.
  • Close all protected doors and windows to bring on the green ready light.
  • Press *, key in the master code, then press 0. The trouble light goes off.
  • BHS-1000C: if your installer turned on the line monitor, a cut phone line shows a trouble while the system is off.
  • If the system is on when the line is cut, only the siren sounds. Nothing is sent to your monitoring company.

  Pages 1 and 2 of the Brinks BHS-1000 (DTI 670-1000) Subscriber Quick Reference CardPages 3, 5 of the Brinks BHS-1000C Panel Introduction and Programming Chart