DAS DL100 - 200 DL200 manuals

Keypad cheat sheet

• Arm (away)your codeor3

  • Close the doors and windows. The green SECURE light (READY on some keypads) must be on, or the system will not arm.
  • Key in your 4-digit code. Each key press gives a short beep.
  • The red ARMED light comes on. Leave through your entry/exit door.
  • Three beeps means the code was not accepted. Press [#] and key it in again.
  • If your installer has turned on Quick Arm, pressing [3] arms the system. It cannot disarm.

  Pages 4 and 5 of the DL200 User Manual
• Arm while home2

  • The DL200 calls this Entry Guard. It works if your installer has turned it on.
  • Press [2]. After 5 seconds the ARMED light comes on, and on an LED keypad the PARTIAL light too.
  • Some zones are left off. If a watched zone trips, the keypad sounds for a set time before the siren.
  • That gives you time to reset the system if it was an accident.
  • To turn Entry Guard off, press [2] again. After 5 seconds those lights go out.

  Page 4 of the DL200 User Manual
• Disarmyour code

  • Come in through your entry/exit door. The keypad gives a steady tone during the entry delay.
  • Key in your code before the delay ends. The ARMED light goes out and the tone stops.
  • If the ARMED light is flashing when you come in, the alarm went off while you were away.
  • Take care, as an intruder could still be inside.

  Page 5 of the DL200 User Manual
• Bypass a zone*zone*

  • Each detector or door contact is a zone. The DL200 calls bypassing isolating.
  • Disarm first. Press [*], the zone number (1 to 8), then [*]. Key several numbers to isolate several zones.
  • If the system is armed, the keypad beeps 3 times after the second [*] to remind you to disarm.
  • On an LED keypad, an isolated zone's light stays on. All isolated zones go back to normal when you next disarm.

  Pages 5, 8 of the DL200 User Manual
• Chime on or off1

  • The DL200 calls chime Day Annunciation.
  • Press [1]. After 5 seconds the keypad beeps to tell you it is on.
  • Opening a watched door or window, or moving in a watched area, then beeps the keypad for one second.
  • Press [1] again to turn it off. After 5 seconds the keypad beeps.

  Pages 7 and 8 of the DL200 User Manual
• Panic alarm*+#

  • Press [*] and [#] together for one second. The siren sounds.
  • If your alarm is monitored, a report can also go to the monitoring centre.
  • Some panic alarms are set to be silent at the premises. Your installer can tell you how yours is set.

  Page 5 of the DL200 User Manual
• Change a codeCuser numbermaster codenew code

  • Use the master code, user 1. Other users are 2 to 15; every code has 4 digits.
  • LCD keypad: disarm, press [C], then follow the prompts for user number, master code and new code.
  • LED keypad: press [*], user number, [#], then your master code.
  • Press [*], user number, [#], then the new code. Finish with [*], user number, [#].
  • To remove a user, give them the master code. After changing the master code, enter the other codes again.

  Page 6 of the DL200 User ManualPage 1 of the DAS LCD Keypad User Guide
• Test the system1

  • Test at least once a month. Press [1] to turn on Day Annunciation.
  • Open each protected door and window. The keypad should beep, and on an LED keypad that zone's yellow light should blink.
  • Walk through each area covered by a motion detector while someone watches the keypad.
  • On an LED keypad, the zone light for each detector should blink.
  • If any test fails or the result is unclear, call your service company.

  Page 7 of the DL200 User Manual
• Trouble lights

  • Keying in your code quietens a pulsing keypad. It does not arm or disarm the system.
  • If the keypad seems stuck, press [#] for one second to reset it. If that fails, call your service company.

  ARMED light blinking	An alarm went off while the system was armed
  SECURE or READY light off	A zone is open. Close or isolate it before arming.
  SECURE or READY light blinking	Alarm memory. It clears when you disarm.
  AC ON or POWER light off	No mains power
  Zone light blinking (LED keypad)	That zone is open
  Zone light on steady (LED keypad)	That zone is isolated
  Keypad pulsing	A day zone was opened
  Three beeps	Code not accepted, a zone open when arming, or a mistake changing codes

  Pages 7 and 8 of the DL200 User ManualPage 1 of the DAS LCD Keypad User Guide