Bosch EDM Solution 2000 / 3000 manuals

Keypad cheat sheet

• Arm (away)your code#orhold#

  • Icon or text codepad (for a touch screen codepad, see its own guide). Key in your code, then press #.
  • Two beeps, the AWAY icon shows and the exit time starts. The codepad beeps every 2 seconds, then one long beep for the last 10 seconds.
  • Unless your installer has turned it off, holding # until two beeps also arms. Newer panels also arm with 0 then #: a factory code that never disarms.
  • A zone still open when the exit time ends is left out until it closes. Opening it after that sets the alarm off.
  • A long beep and no arming means your system won't arm with a zone open: close it or isolate it first.

  Pages 7, 9, 15 of the Sol 2000 3000 Users GuidePages 12 and 13 of the Solution 3000 Quick Installation Manual
• Arm while homeyour code*orhold*orhold0

  • Icon or text codepad (for a touch screen codepad, see its own guide). The panel calls this STAY Mode.
  • Key in your code, then press *. Unless your installer has turned it off, holding * until two beeps also works.
  • Two beeps and the STAY icon shows. One short beep when exit time ends; until then the icon codepad flashes the zones left off.
  • STAY Mode 2: hold 0 until two beeps. To pick the zones it leaves off: master code, 4, #, then each zone number and *, then #.
  • Newer panels come with code 0, which arms but never disarms: if yours has it, key in 0, then press *.

  Pages 7, 16 and 17 of the Sol 2000 3000 Users GuidePage 13 of the Solution 3000 Quick Installation Manual
• Disarmyour code#

  • Icon or text codepad (for a touch screen codepad, see its own guide). Key in your code, then press #. Two beeps tell you it has disarmed.
  • On the icon codepad, a flashing zone number shows a zone that went into alarm.
  • Under threat, add your duress digit to the end of your code, then press #. It disarms and sends a silent duress alarm, if monitored.

  Pages 12, 17 and 18 of the Sol 2000 3000 Users GuidePage 12 of the Solution 3000 Quick Installation Manual
• Bypass a zone**zone*then#

  • Icon or text codepad (for a touch screen codepad, see its own guide). The panel calls this isolating.
  • Press * twice. Three beeps and the STAY icon flashes.
  • Key in the zone number, then *; on the icon codepad its number flashes. Do the same again to undo a zone.
  • Press # when done. Two beeps, and the system is back to disarmed.
  • If your installer has set up code to isolate, start with *, your code, then * instead.

  Pages 8, 19 and 20 of the Sol 2000 3000 Users GuidePages 13 and 14 of the Solution 3000 Quick Installation Manual
• Alarm memorymaster code8#

  • Icon or text codepad (for a touch screen codepad, see its own guide). Key in your master code, then 8, then #. Three beeps.
  • The last 256 events replay, newest first. On the icon codepad they show one at a time on its lights, with a beep each.
  • After you disarm, a flashing zone number on the icon codepad shows the zone that went into alarm.

  Pages 17, 25 of the Sol 2000 3000 Users GuidePage 12 of the Solution 3000 Quick Installation Manual
• Chime on or offhold4

  • Icon or text codepad (for a touch screen codepad, see its own guide). The panel calls this day alarm.
  • Zones 1 to 4, if your installer set them up, beep the codepad while disarmed.
  • Hold 4 until three beeps to turn it on, or until two beeps to turn it off.
  • While it is on, the STAY icon flashes once every 3 seconds, if your installer has turned that on.

  Pages 8, 12, 25 of the Sol 2000 3000 Users GuidePage 13 of the Solution 3000 Quick Installation Manual
• Panic alarm1+3or*+#

  • Icon or text codepad (for a touch screen codepad, see its own guide). Press 1 and 3 together, or * and # together.
  • An audible panic alarm starts. Press 4 and 6 together for a fire alarm, or 7 and 9 for a medical alarm.
  • Your installer can switch these off or make them silent.

  Pages 11, 18 and 19 of the Sol 2000 3000 Users GuidePage 14 of the Solution 3000 Quick Installation Manual
• Change a codemaster code1#user number#new code#

  • Use your master code. Icon and text keypad steps follow; for TS5/TS7 touchscreens, use their own guide.
  • Icon keypad: master code, 1, #. Three beeps; STAY and AWAY flash. Enter the user number (1–32), then #.
  • Enter the new code, then #. Two beeps confirm it. To delete the code, enter * instead of a new code.
  • Text keypad: master code, dash key, 2 2. Select the user with the arrows or user number, then #.
  • Text keypad: enter the new code, then #. Press dash until the save confirmation appears, then #.

  Pages 17 and 18 of the Sol 2000 3000 Users GuidePages 1 and 2 of the Solution 2000 3000 Lcd Alphanumeric Codepad
• Set the date and timemaster code6#datetime#

  • Icon or text codepad (for a touch screen codepad, see its own guide). Key in your master code, then 6, then #. Three beeps.
  • Key in day, month, year, hour and minute, two digits each, in 24-hour time.
  • Press # to save: two beeps. A long beep means a mistake: start again. On the icon codepad the STAY and AWAY icons flash until then.
  • The panel flags a date and time fault every time it has been powered down. Set it again when that happens.

  Pages 21 and 22 of the Sol 2000 3000 Users GuidePage 1 of the Solution 2000 3000 Lcd Alphanumeric Codepad
• Trouble lightshold5

  • Icon or text codepad (for a touch screen codepad, see its own guide). A fault flashes the FAULTS or MAINS icon and the codepad beeps once a minute.
  • Press # to stop the beeping. To see the fault, hold 5 until two beeps.
  • The icon codepad shows a zone number for the type of fault (see the table); hold that number's key to see more.
  • The text codepad shows the fault in words: scroll with the arrow keys, then press the dash key to leave.
  • On the icon codepad, press # to leave. The FAULTS icon stays on until the fault is fixed. For a date and time fault, set the date and time again.

  1	System fault, such as the battery, date and time, phone line or power supply
  2	A wireless detector's battery is low
  3	A zone's tamper has been set off
  4	A detector has seen no movement for the time your installer set
  5	A wireless detector has stopped reporting
  6	Couldn't report to the monitoring company
  7	An output expander or codepad fault
  8	A remote's battery is low

  Pages 8, 20 to 22 of the Sol 2000 3000 Users GuidePage 1 of the Solution 2000 3000 Lcd Alphanumeric Codepad
• Send a test signalhold9

  • Icon or text codepad (for a touch screen codepad, see its own guide). Hold 9 until two beeps. No code is needed.
  • The panel sends a test report to your monitoring company.
  • It works only if your system reports by phone or through a network module.
  • A report that gets through also clears a 'couldn't report' fault (type 6 in the trouble list).

  Pages 22, 24 of the Sol 2000 3000 Users GuidePages 12 and 13 of the Solution 3000 Quick Installation Manual