Moose Z700 / Z900 manuals

Keypad cheat sheet

• Arm (away)your code

  • Check the green READY light is on. If it's off, the zone lights show which area is open.
  • Key in your user code. The keypad beeps and the red ARMED light blinks during the exit time.
  • Leave straight away. The ARMED light goes steady once the system is armed.
  • Took too long? The beeping turns steady as the entry time starts: disarm and start again.
  • A three-second error tone means it didn't arm because something is open.

  Pages 5 and 6 of the z900 usermanPages 5 and 6 of the z700 user man
• Arm while homehold4thenyour code

  • To stay inside, turn the inside detectors off first: hold [4] for three seconds.
  • The inside zone lights flash. Then key in your user code to arm.
  • This also turns off the entry delay: opening the entry door sets the alarm off at once.
  • The inside detectors come back on when you disarm, unless your installer changed that.

  Page 6 of the z900 usermanPage 6 of the z700 user man
• Disarmyour code

  • Come in through your entry door. The keypad sounds a steady tone.
  • Key in your user code. The red ARMED light goes out.
  • If the red ALARM light is on as you come in, an alarm has happened. Leave and call for help.

  Page 7 of the z900 usermanPage 7 of the z700 user man
• Bypass a zone#zone

  • Each detector or door contact is a zone (1 to 6). Disarm first.
  • Press [#] (the bypass key), then the zone number. Its zone light blinks.
  • Repeat for other zones. [#] and the same number again puts a zone back.
  • [#] then [9] cancels all bypasses. [#] then [0] bypasses every open zone, if your system allows it.
  • The blinking stops 30 seconds after the system arms.

  Page 11 of the z900 usermanPage 15 of the z700 user man
• Alarm memoryyour codethen*

  • After an alarm, key in your user code to reset it. The red ALARM light stays on.
  • The zone lights show which areas went off. No zone light means a panic alarm started it.
  • Press [*] to turn the ALARM light off once you've noted the zone.
  • False alarm? Ring your monitoring company straight away.

  Page 8 of the z900 usermanPage 8 of the z700 user man
• Chime on or offhold6

  • With the alarm disarmed, hold [6] for three seconds.
  • Three beeps: chime is on. The keypad then beeps twice when a door or window zone opens.
  • Hold [6] again: two beeps means chime is off. Inside zones never chime.

  Page 10 of the z900 usermanPage 10 of the z700 user man
• Reset smoke detectorshold7

  • After a fire alarm, press [*] to quiet the keypad and siren, then key in your user code to clear it.
  • A yellow TROUBLE light after clearing the alarm may mean a latched smoke detector or faulty wiring.
  • Hold [7] for three seconds to reset the smoke detectors.
  • If TROUBLE stays on, call for service.

  Page 18 of the z900 usermanPage 18 of the z700 user man
• Panic alarmhold1+3orhold*+#

  • Z700R: hold [1]+[3] or [*]+[#] together for three seconds.
  • Z900R: use the separate panic key below the digits: flame, shield or cross. Your installer assigns each key and must enable it.
  • Z900R: press the chosen key. Depending on setup, it may need a three-second hold or two presses within three seconds.
  • Your installer decides which emergency it sends and whether it is silent.
  • To reset, enter your code. Press [*] to clear the ALARM light.

  Page 9 of the z700 user manPages 1, 4, 9 of the z900 userman
• Change a codehold9thenmaster codeuser number#new code

  • With the alarm disarmed, hold [9] for three seconds: three beeps.
  • Key in the master code: two beeps, and the READY and ARMED lights blink in turn.
  • Press the code number (2 to 6, or 1 for the master code), then [#]. Three beeps.
  • Key in the new 4-digit code. A short then a long beep means it's saved, and programming ends.
  • Made a mistake? Press [*] five times and start again.

  Page 14 of the z900 usermanPage 12 of the z700 user man
• Test the systemhold8

  • Disarm and close everything so the READY light is on.
  • Hold [8] for three seconds: three beeps mean test mode.
  • Open each door and window, and walk past each detector. The keypad beeps and that zone's light comes on.
  • Press [*] when you've finished.

  Page 17 of the z900 usermanPage 17 of the z700 user man
• Trouble lightshold2

  • A lit TROUBLE light means the system has a problem. If the keypad beeps, press [*] to quiet it.
  • Hold [2] for three seconds: three beeps, then the zone lights show which trouble (see the table).
  • The lights go back to normal after 8 seconds with no key pressed.
  • A communication trouble clears once the panel gets through. Tell your security company which lights came on.

  ZONE 1	Mains (AC) power has failed
  ZONE 2	Low battery or a blown fuse
  ZONE 3	A supervised zone, such as a fire zone, is open or shorted
  ZONE 4	It couldn't get through to the monitoring centre
  ZONE 5	Memory error: call for service
  ZONE 6	A control station is missing (its data wire is off)
  ALARM lit during the check	Chime is on: not a trouble
  READY or ARMED lit during the check	Inside zones are off, or the entry delay is off: not a trouble

  Pages 10, 20 and 21, 35 of the Moose Z700 Specifications Installation and Programming GuidePages 10, 20 and 21, 35 of the z900 inst