Moose ZX200 / ZX300 / ZX400 manuals

Keypad cheat sheet

• Arm (away)AWAYyour code

  • Close doors and windows, and check the READY light is on. A lit zone light is something still open.
  • Press [AWAY], then key in your passcode.
  • AWAY lights steady while STAY and NIGHT flash for the exit time. Leave before it ends.
  • ZX200/ZX210 or ZX400/ZX410 only: if your installer turned on quick arming, press [AWAY] then [ENTER], or [AWAY] twice.

  Pages 9 and 10, 14 of the moose z200 user guide
• Arm while homeSTAYyour codeorNIGHTyour code

  • STAY is for when people are home: chosen door and window sensors turn on.
  • NIGHT is for bedtime: chosen door, window and inside sensors turn on.
  • Press [STAY] or [NIGHT], then key in your passcode.
  • Pressing [ENTER] during the countdown arms at once and turns off the entry time: opening the front door sets it off.
  • You can swap between STAY and NIGHT without turning it off. From AWAY, turn it off first.

  Pages 7, 9, 11 of the moose z200 user guide
• DisarmOFF CANCELyour code

  • Press [OFF CANCEL], then key in your passcode. The armed light goes out.
  • The same keys silence an alarm. Silence a false alarm quickly and it may not be reported.
  • If the armed light was flashing, the alarm has been reported: ring your monitoring centre.
  • If your installer set up a duress passcode, using it here sends a silent alarm.
  • Coming home to an alarm? Don't go in. Call for help first.

  Pages 2, 9 and 10, 16 of the moose z200 user guide
• Bypass a zone4your code2-digit zoneENTERENTER

  • Each detector or door contact is a zone. If your installer has turned bypass on, a bypassed zone stays off until you disarm.
  • Press BYPASS (the 4 key) and key in your passcode. The READY and TROUBLE lights flash.
  • Key in the zone number (2 digits) and press [ENTER]. Repeat for any other zones.
  • Press [ENTER] to save, or [CLEAR] to cancel.
  • After BYPASS and your passcode, [9] [9] bypasses every open zone and [0] clears all bypasses. Then [ENTER] twice.

  Pages 12 and 13 of the moose z200 user guide
• Alarm memory2your code

  • Press ALM MEM (the 2 key), then key in your passcode.
  • The zones that went into alarm light up briefly, and the READY and TROUBLE lights flash.
  • Silencing an alarm that has been reported puts the keypad into alarm memory by itself.

  Pages 10, 19 of the moose z200 user guide
• Chime on or off6your code

  • Press CHIME (the 6 key), then key in your passcode. Do the same again to turn it off.
  • With chime on, opening an outside door or window zone makes a chime sound.

  Pages 6, 11 of the moose z200 user guide
• Reset smoke detectors7your code

  • Silence the fire alarm first: [OFF CANCEL] and your passcode. Smoke detectors can't be reset while it sounds.
  • Press RST SMOKE (the 7 key) and key in your passcode.
  • The trouble on that zone should clear in a few seconds. If it doesn't, contact your installer.

  Pages 41 and 42 of the moose z200 user guide
• Panic alarmholdthe key with a flame on itorholdthe key with a shield on itorholdthe key with a cross on it

  • ZXLED8/ZXLED12: hold the flame (fire), shield (police) or cross (medical) key for three seconds.
  • These work only if your installer enabled them. On ZX400/ZX410, an enabled double press means two presses within one second.
  • To silence the alarm, press [OFF CANCEL] and enter your passcode.

  Flame picture	Fire
  Shield picture	Police / hold-up
  Cross picture	Medical / auxiliary

  Pages 7, 16 of the moose z200 user guide
• Change a code9master code2user numberENTERnew codeCLEARor9master code5user numberENTERnew codeCLEAR

  • ZX200/ZX210 or ZX400/ZX410 only. Press [9] and your master passcode; READY and TROUBLE flash.
  • Press [2] on ZX200/ZX210 or [5] on ZX400/ZX410. ZX300/ZX310 cannot be programmed from an LED keypad.
  • Key in the user number (1 to 9; on a ZX400/ZX410 two digits, 01 to 50), press [ENTER], then the new 4-digit passcode.
  • Press [CLEAR] to finish. An error tone means that passcode is already in use.
  • A passcode of 0000 switches that user off. Change the factory passcode straight away; your installer can tell you if it is still set.

  Pages 25 and 26, 38 of the moose z200 user guidePages 17, 29 of the zx200 inst
• Trouble lightsOFF CANCELyour codethen1

  • The TROUBLE light means a problem. Press [OFF CANCEL] and your passcode to quiet the sounder.
  • Press VIEW INFO (the 1 key): zones with a problem light up, and bypassed zones flash.
  • Press VIEW INFO again: the zone lights now show a system trouble (see the table).
  • If the TROUBLE light doesn't go out, contact your installer.

  Light 1	Mains (AC) power has failed
  Light 2	The panel's battery is low
  Light 3	Memory error
  Light 4	Communication failure
  Light 5	A keypad is missing
  Light 6	Radio (RF) jamming
  Light 7	Bell fault
  Light 8 or 9	Phone line failure (8), or call RPM failure (9)

  Page 20 of the moose z200 user guide
• Send a test signal8your code4

  • Sends a test to your monitoring centre to check your alarm can reach it. It only works if a central station monitors your system.
  • Turn the system off. Press TEST (the 8 key), key in your passcode, then press [4].
  • It can take a while. Four beeps mean it passed; if it failed, a communication trouble shows a few minutes later.
  • Your passcode must be allowed to run tests. The master passcode can.

  Pages 21, 23 of the moose z200 user guidePage 29 of the zx200 inst