Radionics 4000 - 8000 manuals

Omegalarm 4000 / 8000 and 4012 / 8012 cheat sheet

• Arm (away)your code

  • For the digital arming stations, use your code. On the keyswitch station, use your key instead.
  • Close doors and windows. On a 4012 or 8012 station with a green Ready light, it must be on.
  • Key in your code, or turn the keyswitch. On stations with a red light, it flashes during exit time. Leave now.
  • The red light stays on once armed. It may keep flashing until the arming report reaches your monitoring company.
  • On the 9-key plate, a buzz without a flashing red light means it has not armed. Close open doors and windows.

  Page 1 of the 4000-8000 User GuidePages 3 to 5 of the 4012-8012 User Guide
• Arm while home

  • For the pictured 12-key digital stations with a bottom-right * key; the 9-key plate, ALPHA and keyswitch need their own guide.
  • If your installer has set up perimeter arming, press the bottom-right * key to arm the outside zones while home.
  • There is no exit delay. To go out, disarm first, then arm the whole system with your code.

  Page 4 of the 4012-8012 User GuidePage 6 of the 4000-8000 Installation Manual
• Disarmyour code

  • For the digital arming stations, use your code. On the keyswitch station, use your key instead.
  • Come in only through your delay door. Any other protected door sets the alarm off straight away.
  • When the entry buzzer sounds, key in your code or use your key. The buzzer stops; a red Armed light goes out.
  • Alarm sounding? Key in your code, or use your key, to silence it.

  Page 1 of the 4000-8000 User GuidePages 3 and 4 of the 4012-8012 User Guide
• Reset smoke detectors

  • On a 4000 or 8000, hold the reset button on the alarm's control box (the transmitter) for 3 seconds.
  • Then key in your code at the keypad.

  4000/8000 transmitter reset button	Hold for 3 seconds, then enter your code at the keypad

  Page 1 of the 4000-8000 User Guide
• Panic alarm

  • For the pictured digital station, double-gang plate and single-gang plate with two * keys: press both * keys together.
  • This sends a panic alarm only if your installer has wired that function to a panic zone. Check with your alarm company.
  • The 9-key plate, ALPHA, keyswitch and slim station do not have two * keys; see their own guides.

  Page 6 of the 4000-8000 Installation Manual
• Change a code

  To change your code	Ring your alarm company

  Page 4 of the 4012-8012 User Guide
• Trouble lights

  • For stations with red/green lights, use the table. The 9-key plate has only a red light; ALPHA has a display.
  • On a 4012/8012 digital station, green off with all zones closed and no key buzz can mean a power problem.
  • Check the plug-in transformer and circuit breaker, then call your alarm company. It can still be armed.
  • 4012/8012 with the optional fire test/reset module: a non-stop buzzer means the smoke detectors need resetting or a fire trouble.
  • Your code won't stop it: with the room clear of smoke, press the reset switch once. Still buzzing? Call for service.

  Green light on	Ready to arm, and mains and battery power are normal
  Green light off, keys buzz	Something is open or a beam is blocked, so it won't arm
  Red light off	Not armed
  Red light flashing	The exit time is running, or the arming report is still being sent
  Red light on	Armed
  Red light flashing slowly (short on, long off) while armed	The backup battery is low, such as after a power cut or a long alarm. It stops once recharged
  Light blinking once a second (4000 / 8000)	The battery isn't fully charged, or the bell fuse has blown
  Buzzer non-stop (fire test/reset module fitted)	Smoke detectors need resetting, or a fire system trouble

  Pages 3, 5, 9 of the 4012-8012 User GuidePages 7 and 8 of the 4000-8000 Installation Manual