Paradox EVO manuals

Keypad cheat sheet

• Arm (away)your codeARMorholdARM

  • Close all zones. On the K641 button keypad, the STATUS light is green when all zones are closed.
  • K641: enter your code, press [ARM], then choose areas if asked. Leave before the exit time ends.
  • K656: press [MENU], [1], select Arm, enter your code, then choose areas if asked. Leave before exit time ends.
  • If your installer enabled one-touch arming, hold [ARM] without a code; on K656, hold it for three seconds.
  • Grafica: use its own guide; these ARM-key sequences do not apply.

  Pages 5 and 6, 8 to 10, 17 of the EVO-User GuidePages 9 to 11 of the EVOHD+ User Guide V1.05
• Arm while homeyour codeSTAYoryour code5

  • Stay arms the programmed outer zones while you remain inside. Your code must have permission for this arming method.
  • K641: enter your code, press [STAY], then choose areas if asked. For Instant arming, use [5] instead.
  • K656: press [MENU], [1], select Stay Arm or Instant Arm, enter your code, then choose areas if asked.
  • Instant removes the entry delay. If your installer enabled one-touch arming, holding K656 [STAY] for three seconds Stay arms.
  • Grafica: use its own guide; these STAY-key sequences do not apply.

  Pages 9 and 10, 17 of the EVO-User GuidePages 9, 11 of the EVOHD+ User Guide V1.05
• Disarmyour codeDISARM

  • K656: enter your code during entry time or for one area. Otherwise enter your code, [5], then choose areas. Grafica: use its guide.
  • K641: enter through your entry door, enter your code, then press [DISARM]. Choose areas if asked; red STATUS goes out.
  • Stopping an alarm: key in your code. After a burglar alarm, leave and ring the police from somewhere safe.
  • False alarm? Ring your monitoring company straight away. A fire alarm sounds as a BEEP-BEEP-BEEP from the siren.
  • K641 smoke reset, once smoke has cleared: hold [CLEAR] and [ENTER] together for two seconds.

  Pages 5, 12, 28 of the EVO-User GuidePages 13, 30 of the EVOHD+ User Guide V1.05
• Bypass a zoneyour codeBYPzoneENTER

  • A bypassed zone stays off until you disarm. Your installer and user permissions must allow bypassing; fire zones cannot be bypassed.
  • K641: enter your code, [BYP], then the zone number. Or scroll to a zone and press [BYP].
  • K641: press [ENTER] to save. A long beep means that zone cannot be bypassed.
  • K656: [MENU], [3], your code if asked, [1], then the 3-digit zone number. Press [CLEAR] to save.
  • Grafica: use its own guide; these word-key and MENU-key sequences do not apply.

  Pages 9 and 10 of the EVO-User GuidePages 10 and 11 of the EVOHD+ User Guide V1.05
• Alarm memoryMEM

  • These keys are for keypads with a DISARM key. On a K656 touch keypad, press [MENU] then [4]. On a Grafica, see its own guide.
  • After an alarm, K641 shows 'Alarm in Memory'; K656 prompts you to press [MENU], [4].
  • K641: press [MEM]. K656: press [MENU], [4]. Scroll through the zones that went into alarm.
  • Press [CLEAR] to leave.
  • The memory is wiped after the next alarm, once a code has been entered.

  Page 12 of the EVO-User GuidePage 13 of the EVOHD+ User Guide V1.05
• Chime on or offyour code91zoneACCENTER

  • Chime makes the keypad beep when a chosen zone opens.
  • K641: enter your code, [9], [1], then the zone number; [ACC] switches its chime on or off.
  • K641: press [ENTER] to save, then [CLEAR] to leave.
  • K656: [MENU], [6], your code, [1], zone, [ENTER] to switch chime; [CLEAR] saves, then [CLEAR] exits.
  • Grafica: use its own guide; these ACC-key and MENU-key sequences do not apply.

  Page 24 of the EVO-User GuidePage 26 of the EVOHD+ User Guide V1.05
• Panic alarmhold1+3orhold4+6orhold7+9

  • K641 button keypad: hold both numbered keys together for two seconds.
  • Grafica: hold one panic picture key for two seconds. K656: press and hold one panic picture key.
  • [1]+[3] or shield: emergency; [4]+[6] or warning triangle: auxiliary; [7]+[9] or flame: fire.
  • Your installer must enable the panics and chooses what each reports and whether the siren sounds.

  Page 24 of the EVO-User GuidePage 26 of the EVOHD+ User Guide V1.05
• Change a codemaster code0ACC001new codeENTERCLEAR

  • These keys change user 001 (System Master) on a keypad with DISARM. Grafica: see its own guide.
  • Key in the current master code, then [0], [ACC], [0], [0], [1], the new code, [ENTER], then [CLEAR].
  • K656: [MENU], [9], [1], master code, [1], [0], [0], [1], new code, then [ENTER] to continue.
  • K656: follow the card, remote and user-label screens, then press [ENTER] to save and exit.
  • DISARM-key models: other users need option and area screens. Delete a user with [CLEAR] at the new-code step, then [ENTER].

  Pages 13, 15 and 16 of the EVO-User GuidePages 14, 17 and 18 of the EVOHD+ User Guide V1.05
• Set the date and timeyour codeTRBL8timedateENTER

  • These keys are for keypads with DISARM. K656 uses a different menu below; Grafica owners need its guide.
  • DISARM-key LCD: code, [TRBL], [8]. Use the up arrow to pick digits; enter 24-hour time, then year/month/day. Press [ENTER].
  • K656: [MENU], [9], [2], then your code. Use the up arrow to pick digits; follow its 12- or 24-hour display, then year/month/day.
  • K656: press [ENTER] to save. DGP2-648BL LED: code, [TRBL], [8], 24-hour time, yyyy/mm/dd, then [CLEAR].
  • 'Clock Loss' in the trouble list means the time and date were reset and need setting again.

  Pages 22 to 24 of the EVO-User GuidePage 25 of the EVOHD+ User Guide V1.05
• Trouble lightsTRBL

  • These keys are for keypads with a DISARM key. On a K656 touch keypad, press [MENU] then [5] (its screen says so). On a Grafica, see its own guide.
  • K641 shows 'Trouble(s) [TRBL] to View'; K656 prompts you to press [MENU], [5].
  • If your installer turned on trouble beeps, a K641 beeps until you press [TRBL] or the trouble clears.
  • K641: press [TRBL]. K656: press [MENU], [5]. Scroll through the trouble groups; press a trouble number for details.
  • Ring your installer about any trouble except Clock Loss, which you can fix by setting the time and date.

  Group 1: System	[1] power cut, [2] backup battery trouble, [5] siren not connected
  Group 2: Communicator	[1] no phone line, [2] to [5] couldn't reach the monitoring company, [6] couldn't reach the installer's software
  Group 5: Zone tamper	The zones shown have been tampered with
  Group 6: Zone low battery	A wireless device in the zone shown needs a new battery
  Group 7: Zone fault	A wireless device has lost contact, or a smoke detector has a wiring or CleanMe fault
  Group 8: Clock loss	The time and date were reset: set them again

  Pages 21 and 22 of the EVO-User GuidePage 23 of the EVOHD+ User Guide V1.05
• Send a test signalmaster code0STAY

  • Use these when your installer or monitoring company asks. On a Grafica keypad, see its own guide.
  • K641: key in the master code (or a code with the Master feature), then [0] and [STAY]. A test report goes to your monitoring company.
  • K656: ring your monitoring company first, then press [MENU], [9], [6], [1] (TEST REPORT) and key in the master code.
  • That test checks the connections and can send a report, if your installer set it up. The K641's version: ring first, then your code and [8].

  Pages 24, 27 of the EVO-User GuidePages 26, 28 of the EVOHD+ User Guide V1.05